As of July 1, 2024, the 1-888 phone service in no longer available. Use the Contact Us Button above for support.
Browse Catalog
As of July 1, 2024, the 1-888 phone service in no longer available. Use the Contact Us Button above for support.

Curvable Laser Cut Wood Ties For On3 #7 Turnouts - Right

TW-ON3-T-7-R
Slide

Built When Ordered

Production Time: 2 to 3 days

The TW-ON3-T-7-R will be automatically added to our production queue when it is ordered.

PRICE : $20.99

Fast Tracks TwistTies provides the modeler with a way to build low cost, realistic looking, and accurate On3 #7 curved or straight turnouts with ease using all wood tie construction with spikes & rail. No soldering is required! Combined with our TwistTie fixed and flexible crosstie strips, you can finish all your trackwork in no time! Each TwistTie is laser cut as a single-piece lattice of pre-spaced, pre-drilled wood ties that:

  • Can be curved to fit any desired radius while maintaining the turnout size
  • Include pre-drilled spike holes that ensure accurate gauging & geometry
  • Makes turnout construction faster & easier than traditional methods
  • Takes the guesswork out of hand laying curved & straight turnouts
  • Includes etched guidelines to verify rail location
  • Pre-spaced ties eliminate tie laying tedium
  • Uses stainable wood ties
  • Are NMRA compliant

TwistTies are cut from Baltic Birch plywood custom sawn in Finland specifically for Fast Tracks. Like the prototype, the wood grain on our TwistTies runs perpendicular to the rails. The ties are 0.1" (2.5mm), 5 scale inches thick and 0.15" (3.8mm) 7 scale inches wide. They will match all popular commercially available wood ties, including wood ties available from Fast Tracks. The ties will also match all popular commercial track and our line of QuickSticks. Each TwistTie can be used to construct one On3 #7, Right hand turnout using code 70, 83 or 100 rail and are designed to work with Micro Engineering small spikes. If you order Fast Tracks TwistTies, we highly recommend that you consider purchasing a matching Frog Helper soldering jig and PointForm tool. This will make the construction of the frog and switch points much easier. You may also consider adding some of our CopperHead PC Board turnout ties (for the throwbar) to your order. If you are building curved turnouts, the rail will need to be pre-formed. Our Rail Roller bending tool will make this easy.

Note: Using our Assembly Fixtures, you will always get better and faster results with less effort. However, if you only need to build a small number of turnouts, curved turnouts of any radius, or if you prefer all wood tie construction, then TwistTies may be a better option for you.

Craftsman Series ToolsThis product is part of our Craftsman Series of tools designed for modelers who want to go that 'extra mile' to produce outstanding trackwork. It would help if you were prepared to spend extra time and effort learning how to use this product. Click here to learn more about our Craftsman Series of tools.

Reviews

There are no reviews yet.

Be the first to review “Curvable Laser Cut Wood Ties For On3 #7 Turnouts - Right”
PARAMETERVALUEDETAILS
Default Turnout Length17" (432 mm)This is the length of the turnout on the QuickSticks. Measured from end tie to end tie.
Diverging Route Angle8.13 (Decimal)
8°/7'/48"(D/M/S)
1:7 (Ratio)
Decimal = Frog angle in decimal degrees
D/M/S = Deg/Min/Sec
Ratio = Frog angle expressed as a ratio
Diverging Route Radius54" (1372 mm)The minimum radius in a straight turnout.
Tie Spacing (Prototype)22" (559 mm)Tie spacing center of tie to center of tie.
Tie Size (Model)L - 1.75" (44 mm)
W - 0.15" (4 mm)
H - 0.1" (3 mm)
The actual size of the tie.
Tie Size (Prototype)L - 7' (2.1 m)
W - 7"(178 mm)
H - 5" (127 mm)
The original tie size that the model was based on.
Track Gauge0.76" (19 mm)The distance between the stock rails.
SizeL - 17" (432 mm)
W - 3.5" (89 mm)
H - 0.1" (3 mm)
The physical size of the product
Weight0.1 lbs (0.045 kg)
Material2mm thick 3 Ply Baltic Birch
Building Curved (and Straight) Turnouts With Fast Tracks TwistTies

TwistTies offer an alternative to building switches using an assembly fixture, PC Board ties, and solder. Instead, the switch is built using a pre-cut all wood tie lattice. This document provides detailed instructions.

Using the Frog Helper To Build Curved or Straight Turnout Frog Points

The Frog Helper tool works in the same manner as a full-sized assembly fixture but is specifically designed for building frog points. These instructions explain how to use the tool to construct curved or straight points and apply to all scales.

Using The Fast Tracks PointForm Tool To Build Switchpoints

The PointForm tool is not only used to file Frog points. It can also be used to file perfect switch points as well. Here is how it works.

How To Use Fast Tracks SweepSticks

How Fast Tracks SweepSticks can be used to precisely form a perfect radius in flextrack

Using The Fast Tracks Frog Helper To Build Curved Frog Points

The Fast Tracks Frog Helper tool can be used to build precision frogpoints for both straight and curved switches. Here we demonstrate how to build frogpoints for a curved turnout.

Using The Fast Tracks Frog Helper To Build Straight Frog Points

Building precision switch frog points is greatly simplified by using the Fast tracks Frog Helper tool along with the PointForm filing tool. This video demonstrates how.

Bending & Straightening Rail With The Fast Tracks Rail Roller

Bending rail into long smooth curves for curved trackwork can be challenging. The Fast Tracks Rail Roller tool makes this difficult job quick and easy. Plus it can straighten bent rail as well. This video shows you how it works.

Hand Laying Track Using Fast Tracks TwistTies

Fast Tracks TwistTies provides the craftsman with a way to build low cost, realistic looking and accurate all wood tie trackwork using laser cut wood ties, spikes & rail.

Using The Fast Tracks PointForm Tool To Build Frogpoints

Building highly accurate frogpoints is made fast and simple with the Fast Tracks PointForm tool. Here is a detailed demonstration showing you how it works.

Using The StockAid Tool To File The Base Of The Stockrail

Video demonstration on using the StockAid tool to remove the base of the stockrail.

Fast Tracks Video Channel

Visit our growing collection of track building demonstration videos

Fast Tracks Knowledge Base

In addition to an extensive Q&A section, we also offer a full library of track building documents.

Items you may want to include in your order​

18 in stock

$12.50

23 in stock

$89.95

22 in stock

$3.75

PREVIOUSLY VIEWED PRODUCTS